Tunnel – DynDNS configuration parameter: “DYNDNS_”
MTXTunnel version 5.0 and above include the “DYNDNS_” parameter. They refer to the DynDNS service which allows you to assign a DNS name to a dynamic IP address, in such a way that a DNS with the format “mymodem.dyndns.org” will always take note of the IP address obtained by the network operator at all times. MTXTunnel connects with […]
Tunnel – SMS Configuration parameter: “SMS_”
MTXTunnel has a lot of SMS features. SMSs can be used (sent and received) to configure, report, start/stop any service, etc. You need to configure the SMS messaging feature with the following parameters: SMS_sendIP Description: MTXTunnel starts the 4G/3G/2G connection and associated services (tunnel, WebServer, telnet …) if it receives a missed call or an […]
Tunnel – FIREWALL configuration parameters: “FIREWALL_”
MTXTunnel by default allows access from any IP address. If you enable a firewall, your system will be secure as you will avoid unauthorized access. This way, only configured IP (or DNS) addresses can connect and access MTX-Tunnel and the other services (GPRS serial tunnel, WebServer, Telnet…). FIREWALL_enabled Description: Parameter to enable firewall and to enable […]
Tunnel – ALARM Configuration parameter: “ALARM_”
MTXTunnel can send SMSs when the level of any digital input changes. This can be performed with the GPRS tunnel activated at same time. ALARM_gpioEnabled Description: This parameter will activate this SMS alarm feature when the digital input level changes. Possible values: on, off Default value: off Additional notes: Each platform type has its own specific input […]
Tunnel – UDP configuration parameter: “UDP_”
These parameters are related to MTX-Tunnel data communication using the UDP protocol. It is needed in the GPRS (UDP) – Serial (RS232/485) tunnel. UDP_IP Description: end IP address where MTX-Tunnel will send data to in UDP protocol. MTX-Tunnel needs be set in UDP mode (MTX_mode: udp). Possible values: IP address format XXX.XXX.XXX.XXX. DNS text string […]
Tunnel – TCP Configuration parameters: “TCP_”
This important configuration parameter relates to TCP protocol communication in MTX-Tunnel. They are mandatory when using 2G/3G/4G TCP – Serial RS232/485 tunnel in client (MTX_mode: client) or server mode (MTX_mode: server) TCP_IP Description: IP server address that MTX-Tunnel will connect to if it is client configured (MTX_mode: client). Possible values: IP address format XXX.XXX.XXX.XXX or DNS […]
Tunnel – GPRS connection configuration parameters: “GPRS_”
The following parameters are mandatory. They make reference to the MTX-Tunnel connection parameters related to the network operator. It depends on the SIM card and provisioned 2G/3G/4G service. Ask your network operator for further information. GPRS_apn, GPRS_apn2 Description: 2G/3G/4G Access Point Name -APN- Possible values: <100 characters text string Default value: movistar.es Additional notes: Some […]
Tunnel – Wakeup Configuration Parameter: “WAKEUP_”
The previous MTX-Tunnel V5 version could only be used for GPRS-serial tunnel Gateway in the following ways: 100% active after modem power-up X minutes active upon demand, after receiving an SMS with special text string “mtxtunnel on” or when receiving a missed call from an authorized configured phone number From version 5.0 more features have been added […]
Tunnel – WebServer Configuration Parameters: “WEBSERVER_”
WebServer configuration parameter starts with “WEBSERVER_”. MTX-Tunnel features a small WebServer which you can easily access with Internet Explorer software and check any modem’s state, network information, input state, or you could change a digital output, etc. WEBSERVER_enabled Description: specifies if the MTX-Tunnel webserver should be activated or not. Through the webserver you can visualized easily the […]
Tunnel – Telnet Configuration Parameters: “TELNET_”
Telnet configuration parameters start with a “TELNET” prefix. Telnet is recommended to remotely send AT commands, to change some configuration parameters or to find out the status of the remote modem with MTX-Tunnel. It is important to understand that Telnet will only work if the GPRS link has been established previously. You can see TELNET […]
Les accès par défaut sont :
Saisir le mode de connexion « Ethernet » ou « modem » :
Dans le cas d’une configuration par Ethernet, veiller à ce que les paramètres IP soient compatibles avec l’accès au serveur d’après la configuration du réseau local du concentrateur. Dans le cas d’une connexion par Ethernet, la configuration doit être compatible avec la topologie du réseau local du concentrateur afin qu’il puisse accéder aux serveurs. Cette configuration se fait via la page de configuration « Networks » (voir chapitre 3.2.2.3 : « Réseaux (Networks) »).
Dans le cas d’une connexion par modem, la configuration du modem doit être correcte avant de pouvoir effectuer une connexion. Cette configuration se fait dans la page de configuration « Modem » (voir chapitre 3.2.2.4 : « Modem »).
Les paramètres des serveurs à configurer au minimum sont les suivants :
Il faut donc configurer les champs : « Interface », « Type », « Server type », « Address », « Port », « Login » et « Password ».
Les autres champs peuvent être laissés aux valeurs par défaut à condition que les répertoires aient été créés correctement auparavant. Voir chapitre 3.1.2 : « Fichiers de configuration » pour plus de détails.
Attendre. Le concentrateur va redémarrer avec sa configuration usine.
